Air Suspension Compressor Pump For 14-21 Land Sport L494 L560 L462

Compatibility Chart

1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).

2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.

3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).

Land Rover Range Rover 2020-2021 L4 2.0L Turbocharged Sport Utility

Land Rover Range Rover 2016-2021 V6 3.0L Turbocharged Sport Utility

Land Rover Range Rover 2014-2019 V6 3.0L Supercharged Sport Utility

Land Rover Range Rover 2014-2021 V8 5.0L Supercharged Sport Utility

Land Rover Range Rover Sport 2016-2017 V6 3.0L Turbocharged Sport Utility

Land Rover Range Rover Sport 2014-2017 V6 3.0L Supercharged Sport Utility

Land Rover Range Rover Sport 2014-2017 V8 5.0L Supercharged Sport Utility

Air Suspension Structure:

Removal Guideline:

CAUTION: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in
the instructions or in a different sequence.

To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for
additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath
the vehicle if it is not adequately supported, as serious injuries and death can occur.

1. RAISE THE VEHICLE.

FIGURE 1

2. IN THE BACK OF THE VEHICLE, REMOVE THE SPARE TIRE COMPARTMENT COVER. (FIGURE 1)

3.REMOVE THE SPARE TIRE. (FIGURES 2, 3)

4.REMOVE THE PROTECTIVE PIECES AND ACCESSORIES SURROUNDING THECOMPRESSOR

COMPARTMENT. (FIGURES 4, 5, 6)

5.LOOSEN AND REMOVE THE TWO COMPRESSOR HOUSING BOLTS. (FIGURES 7, 8)

6.LOOSEN THE COMPRESSOR HOUSING UNIT BY RAISING SLIGHTLY AND SLIDING THE CLIP

AWAY FROM ITS RESPECTIVE SLOT, FREEING THE UNIT. (FIGURES 9, 10)

7.FLIP THE COMPRESSOR HOUSING UNIT OVER. LOOSEN AND REMOVE THE THREE COMPRESSOR

MOUNTING FASTENERS. SAVE FASTENERS FOR RE-USE. (FIGURE 11)

8.REMOVE THE WIRE HARNESS PANEL COVER. (FIGURES 12, 13)

9.REMOVE ALL OF THE COMPRESSOR HOUSING CLIPS. (FIGURE 14)

10.REMOVE THE COMPRESSOR HOUSING COVER. (FIGURE 15)

11.PULL OUT THE COMPRESSOR JUST ENOUGH TO ACCESS THE WIRING HARNESS AND

HOSES. (FIGURE 16)

12.REMOVE THE COMPRESSOR HOUSING MOUNTING HARDWARE AND SET ASIDE FOR INSTALLATION.

(FIGURE 17)

13.DISCONNECT THE TWO ELECTRICAL CONNECTORS. (FIGURES 18, 19, 20)

14.LOOSEN AND DISCONNECT THE AIR LINE. (FIGURES 21, 22)

15.REMOVE THE COLLET AND VOSS FITTING FROM THE AIR LINE. (FIGURES 23, 24, 25)

16.REMOVE THE AIR DRYER. (FIGURE 26)

17.LOOSEN AND REMOVE THE THERMAL SENSOR HARNESS. (FIGURES 27, 28)

18.REMOVE THE COMPRESSOR. (FIGURE 29)

19.REMOVAL COMPLETE.

Installation Guideline:
Installation is in reverse order of air suspension compressor pump removal.

Warning & Notice:

1.When the air compressor being replaced, the matching relay must be replaced according to the corresponding vehicle. If there is something wrong with the relay which leads the compressor to continuous operation without any break, it will burn out the electric motor or other plastic part.

2.When the air compressor being installed, the critical parts such as rubber shock pad and damping spring must be fully fixed on the stand without short installation or missing installation (The air compressor is unequipped with parts). With the anti-vibration parts of short installation or missing installation, a loud noisy instance will happen when the air compressor is working for the sake of resonance.

3.Distribution valve, shock absorber, air tank and tube connector must be checked after air compressor installed to ensure air-tightness. The lifespan of the air compressor will be shortened if the leakage exists.

4.Increased noises while the compressor is running may be caused by a non-functioning compressor mounting. Change the rubbers and springs of the mounting in any case.

5.A porous hose often is the cause for a breakdown of the compressor. Change the hose and preferably also the filter and noise absorber, because we do not want the compressor to breakdown because of these.

6.Change the relays before installing the compressor even if it seems to still work. This is also a specification by the car manufacturer. Be sure to change the right relays. Relays look similar, that is why there is a risk to change the wrong relays.

7.Be sure to check whether the system is leakproof after repairing. The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature. Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes. On the day after measure these heights again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run.

OEM Part Number:

LR121140, LR037070, LR045734

LR047172, LR052301, LR056304

LR069691, LR069692, LR069693
LR083993, LR108984, LR108985

LR121263,LR140034

Item Specifics

Brand: Partsmarket2018
Items Included: Compressor
Type: Air Compressor Pump
Placement on Vehicle: Front Rear Left Right
Features: Easy to Replace
Shock Absorber Type: Gas
Mounting Style: Screw-On
Manufacturer Part Number: PMT117971BS-2
OE/OEM Part Number: LR121140 LR037070 LR045734 LR047172
Manufacturer Warranty: 1 Year
Material: Iron Aluminium Alloy Rubber
Year: 2014-2021
Performance Part: Yes
Universal Fitment: No
Model: Range Rover Range Rover Sport
Compatible Makes: Land Rover
Interchange Part Number: LR052301 LR056304 LR069691 LR069692 LR069693
Fitment Type: Direct Replacement
Superseded Part Number: LR083993 LR108984 LR108985 LR121263 LR140034
Engine: L4 2.0L V6 3.0L V8 5.0L